收藏本站
BU9844GUL-W (16Kbit)
Operational Notes
Datasheet
1.
2.
3.
4.
5.
6.
7.
8.
9.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power
supply pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Separate the ground and supply lines of the
digital and analog blocks to prevent noise in the ground and supply lines of the digital block from affecting the analog
block. Furthermore, connect a capacitor to ground at all power supply pins. Consider the effect of temperature and
aging on the capacitance value when using electrolytic capacitors.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
Thermal Consideration
Should by any chance the power dissipation rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. The absolute maximum rating of the Pd stated in this specification is when
the IC is mounted on a 70mm x 70mm x 1.6mm glass epoxy board. In case of exceeding this absolute maximum
rating, increase the board size and copper area to prevent exceeding the Pd rating.
Recommended Operating Conditions
These conditions represent a range within which the expected characteristics of the IC can be approximately obtained.
The electrical characteristics are guaranteed under the conditions of each parameter.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush
current may flow instantaneously due to the internal powering sequence and delays, especially if the IC
has more than one power supply. Therefore, give special consideration to power coupling capacitance,
power wiring, width of ground wiring, and routing of connections.
Operation Under Strong Electromagnetic Field
Operating the IC in the presence of a strong electromagnetic field may cause the IC to malfunction.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may
subject the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply
should always be turned off completely before connecting or removing it from the test setup during the inspection
process. To prevent damage from static discharge, ground the IC during assembly and use similar precautions during
transport and storage.
10. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
23/26
TSZ02201-0R2R0G100470-1-2
17.Sep.2013 Rev.002
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BU9847GUL-WE2 IC EEPROM 4KBIT 2WIRE VCSP50L1
BU9880GUL-WE2 IC EEPROM 64KBIT 2WIRE VCSP50L1
BU9882FV-WE2 IC EEPROM 2KBIT 400KHZ 14SSOP
BU9883FV-WE2 IC EEPROM 6KBIT 400KHZ SSOP16
BU9889GUL-WE2 IC EEPROM 8KBIT 2WIRE VCSP50L1
BU9891GUL-WE2 IC EEPROM 4KBIT VCSP T/R
BU9897GUL-WE2 IC EEPROM SERIAL VCSP50L2
BU99901GUZ-WE2 IC EEPROM 32KBIT 2WIRE VCSP
相关代理商/技术参数
BU9847GUL-W 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS
BU9847GUL-W_10 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS
BU9847GUL-WE2 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial-2Wire 4Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
BU98570CH-3BW 制造商:ROHM 制造商全称:Rohm 功能描述:65,536 Colors 98RGB x 70 STN LCD control driver
BU98582CH-3BW 制造商:ROHM 制造商全称:Rohm 功能描述:65,536 Colors 104RGB x 82 STN LCD control driver
BU98664CH-3BW 制造商:ROHM 制造商全称:Rohm 功能描述:65,536 Colors 132RGB x 164 STN LCD control driver
BU9873F-GTE2 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 8-SOIC (0.173", 4.40mm Width) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 类型:时钟/日历 特性:警报器，闰年 存储容量:- 时间格式:HH：MM：SS（12/24 小时） 日期格式:YY-MM-DD-dd 接口:I2C，2 线串口 电压 - 电源:1.8 V ~ 5.5 V 电压 - 电源，电池:- 电流 - 计时（最大）:1μA ~ 1.35μA @ 3V ~ 5.5V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.173"，4.40mm 宽） 供应商器件封装:8-SOP 标准包装:1
BU9873FJ-GTE2 功能描述:Real Time Clock (RTC) IC Clock/Calendar I2C, 2-Wire Serial 8-SOIC (0.154", 3.90mm Width) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 类型:时钟/日历 特性:警报器，闰年 存储容量:- 时间格式:HH：MM：SS（12/24 小时） 日期格式:YY-MM-DD-dd 接口:I2C，2 线串口 电压 - 电源:1.8 V ~ 5.5 V 电压 - 电源，电池:- 电流 - 计时（最大）:1μA ~ 1.35μA @ 3V ~ 5.5V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:* 标准包装:1